toille27 3 Posted June 10, 2014 Share Posted June 10, 2014 (edited) Hi, I am new to this forum and wanted to share my experience of installing a keyless entry system in my 2014 Chevy Spark LS. After much research, including this forum I had problems finding a comprehensive thread so here is my payback to the many times someone else helped me out.... I want to preface the fact that if I knew pre-install what I know now I may have paid someone to do this if it were only $300 as it took me way too long (another reason for my post). Note this installation is independent of the existing car with the exception of the power connection to the fuse box and the ground wire connection to the car chassis (and mechanical fastening of the actuators); translated don't worry about any existing wiring colors. My materials from Amazon: Pipeman's CDLS4 Actuator kit http://www.amazon.com/gp/product/B00BXKR6RQ/ref=oh_details_o05_s00_i00?ie=UTF8&psc=1 Bulldog KE1702 Keyless Entry Kit http://www.amazon.com/gp/product/B000CS9Q6E/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1 Trim removal tools http://www.amazon.com/gp/product/B00HPDK5CS/ref=oh_details_o05_s00_i02?ie=UTF8&psc=1 Fuse tap (make sure it fits GM cars as not all mini fuses have the same configuration, learned hard way and had to modify mine) Miscellaneous electrical connectors Facts about my 2014 LS... There is no existing wiring inside the doors for the power locks (except a wire that connects to the drivers side jamb latch where it secures to the bolt on the body of the car, could not figure out what it was for). Each door has a plastic molex connector that seals the door wire penetration to the frame. The existing harness wiring at the front drivers side door is so tightly secured to other wiring it is impossible to get slack to loosen the front drivers side door molex. The front passenger side door molex plug falls adjacent to a structural bracket and makes interior access to the molex impossible. The rubber boots that go from the molex plug to the door have very little extra room and make it very hard to fish wires especially in the bent position. The front door molex connector hits the door when in the fully open position so removal of the plug is impossible and even if one did get it apart I have no idea how to gain access to reassemble. The rear door molex connectors have a few inches of slack and I did find that they can be removed from the frame and disconnected. There is one screw in each door handle well, below a fitted rubber base piece that pops out (see photo). That is the only screw on each door that needs to be removed, the remainder of the door is held with plastic friction fasteners. The front door lock mechanism is inside the door cavity and the rear door lock mechanism is between the inside of the door body and the removable door panel, you will see in my photos. Facts about the install: The Pipeman actuator kit wiring (blue and green wires) is just the right length for the spark within a few inches (hard to believe) so don't leave any slack anywhere. You will not use the relay control board that comes with the Pipeman kit. The Bulldog controller will connect directly to the actuator wires per the diagram attached. The Bulldog kit comes with one automotive relay should you wish to connect other systems to the keyless entry (dome light, parking light, etc.) so if you are connecting more than one indicator you will need extra relays sold separately. The fuse built into the Bulldog controller is 15 Amps so make sure your positive 12 VDC fuse tap is at least 15 Amps, I blew a 5 Amp fuse. You will need to remove the front doors to properly install the front door actuator wiring through the molex plugs (see photos). The actuators will fit in the door cavity easily, however the front doors inside handle rod interfere with the actuator rod and you will have to bend around it (see photo). Rear doors-Make sure you remove the plastic trim block at the back of the rear door window first prior to removing the panel below it. Front doors-Make sure you remove the plastic trim surrounding the manual side mirror adjustment arm first prior to removing the panel below it. Here is the wiring diagram for the KE1702 (ignore reference to 2 doors and pretend 4 are shown): https://docs.google.com/document/d/1o1Q-edaIQ1D_ljnXsVr6K4nJNADJ8kSO-liEhQsOkmQ/edit?usp=sharing The diagram works exactly as shown except the green/black wire from the bulldog controller goes to the blue actuator wire and the blue/black wire from the bulldog controller goes to the green actuator wire. Front Door Removed https://docs.google.com/document/d/1C7_hBFPveYH3W15HQE0jbtz4s3j_y68GbuwuFfZr2Sg/edit?usp=sharing Molex Plug Front Door https://docs.google.com/document/d/1d2py9ijNSfHB2KL64Brj6IiLeVJOpKib0Q7S2dTZeww/edit?usp=sharing https://docs.google.com/document/d/1b7qjmZYM3sFmdkN5SfA-T0FjNQ_aGOnt764CJqViMcs/edit?usp=sharing Inside Front Drivers Door https://docs.google.com/document/d/1iCwFGP5gU4E1E8YDuTZLlJ_oLWBCU9hnP6BdOiriNdw/edit?usp=sharing Front Door Screw Locations https://docs.google.com/document/d/1hODyaRMzLfZ4JCn1msOyYxIfQZ_EiymgbODJbC-Lpqk/edit?usp=sharing Passenger Rear Door. I wanted the actuators inside the door cavity so the trim won't interfere with the actuator rods. I'm not a welder so don't make fun... https://docs.google.com/document/d/1BdyhZ5SjfDkpzSFb8W0JIE1Mit8R9f2dLjSfKjAhsCw/edit?usp=sharing Drivers Side Rear Door. The blue tape is covering wet Locktite Go2 Glue for vibration and preventing loosening screws. https://docs.google.com/document/d/1CZ8dMcj5VoVWWszSDw6xKfHX7zu1ycQAE3cH1d2QJRk/edit?usp=sharing Screw on Door https://docs.google.com/document/d/1J5mm8a_iMFuWJhOU0A6u4xZMQ3drqDBzyK8Q-1N77eg/edit?usp=sharing Ground Wire Connection https://docs.google.com/document/d/1dBREw8xqiVo5i9-lrYgF2gqg9lvVAkGjn4-m8HFey7M/edit?usp=sharing Power Connection https://docs.google.com/document/d/1neTZ8oy-HUju2fyZCJomDX7AfFFcjJuMq3mlVymaiWE/edit?usp=sharing Edited June 10, 2014 by toille27 SilentSpectre, Han Beike and naumanos1 3 Link to post Share on other sites
psquare75 35 Posted June 11, 2014 Share Posted June 11, 2014 Huh. I might do my father's for him. Thanks for all this! Link to post Share on other sites
WaltK 305 Posted June 11, 2014 Share Posted June 11, 2014 Got to hand it to you, quite a project.... Link to post Share on other sites
Rhoov 0 Posted June 20, 2014 Share Posted June 20, 2014 toille i have to hand it to you for your tenacity in doing this and documenting it so well and concise for the rest of us. I also want to thank you for getting me out of doing this to my wife's car. She saw the pic of the drivers door off of the car and decided that she can live with manual door locks! i will keep this bookmarked in case she changes her mind (like next week). Thanks again! Robert Link to post Share on other sites
walt2137 1 Posted August 2, 2014 Share Posted August 2, 2014 Toiller thanks for the great write up it convinced me that I dont really need door locks as much as I thought. Walt Link to post Share on other sites
Hobbiest 0 Posted April 22, 2016 Share Posted April 22, 2016 Outstanding job on your detailed instructions & pictures. I just bought my daughter a new 2015 LS and found your post in my research. It is exactly what I needed. I know I can do this BUT should I be. I've always tried to keep my son from messing with his cars. If it ain't broke don't fix it. But he ignores me and puts in stereos, new rear ends, headers, High intensity lights, etc and it just drives me nuts. Now here I am not practicing what I preach and going against all better judgment. I think I will see how my daughter does with them being manual for awhile. If I can keep her from having bunch of keys on the ring so don't scratch the paint when opening and she can reach the locks easily enough I may leave well enough alone. The one picture showing the plastic door barrier was nice. I like to know what I'm dealing with before I pop those door panels off. I've replaced window regulators and such. Usually the vehicles are older and some have sort of a harder thickness door barrier that gets brittle and falls apart when taking off. This one don't look too bad. I will only do the front two doors if I do decide to do it. It's just her and my granddaughter who rides in front. Thanks again Link to post Share on other sites
Retired old Gearhead 201 Posted April 23, 2016 Share Posted April 23, 2016 That's alot of work to spoil your daughter with power locks! I think younger ppl are more interested in the music aspect and hands free phone in a car. To me hands free voice activated phone is a must and just swell when I get a call while in Miami 'nutsville' traffic. Link to post Share on other sites
toille27 3 Posted May 1, 2016 Author Share Posted May 1, 2016 (edited) I wanted to add to this old thread that I am going on 2 years with the keyless entry and everything still works great (knock on wood). I also wanted to add that the two existing wires that go to the drivers side door latch (appears to be a 12VDC jamb release) were probably for OnStar to remotely open the drivers side door. I eventually tied the keyless entry into the rear hatch lock as well using an automotive relay tied into the dashboard latch button. It simulates a press of the dash button when I hit the key fob lock/release button. Edited May 1, 2016 by toille27 Link to post Share on other sites
ChevyBeat 28 Posted August 31, 2018 Share Posted August 31, 2018 Hi, anyone tried removing rear door panel? I asked here as that is part of this job. I am installing door LED strip as puddle lamp but stuck with rear door panel. I already tried pulling it apart but its not moving. Also, I want to know how to remove mirror crank handle. Link to post Share on other sites
chevysparknightfallgray 0 Posted September 9, 2023 Share Posted September 9, 2023 I apologize for the 9-year-old necropost, but I noticed the images in this post are stored in Google Docs. The image in the KE1702 wiring diagram is already unavaliable, so I figure I would reupload the images, just in case the images get lost eventually. I uploaded them to Imgur and also attached them to this post. Front Door Removed Molex Plug Front Door (1) Molex Plug Front Door (2) Inside Front Drivers Door Front Door Screw Locations Passenger Rear Door Drivers Side Rear Door Screw on Door Ground Wire Connection Power Connection Link to post Share on other sites
camrossrs99 0 Posted January 13 Share Posted January 13 Thanks for the pictures I just got done doing this to mine. I felt it was easier just to remove all doors to feed wires into each door. The pictures you posted made this so much easier. Link to post Share on other sites
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now